Example Code for Arduino-Chlorophyll Data Monitoring

Hardware Preparation

• DFRduino UNO R3 (or similar) x 1
• Gravity: Active Isolated RS485 to UART Signal Adapter Module x1
• RS485 Water Quality Chlorophyll Sensor x1

Software Preparation

• Arduino IDE (latest version recommended)

Wiring Diagram

If the power of the RS485 device is small and the required current is less than 12V-160mA, the RS485 to UART signal conversion module does not require a 12V external power supply, making wiring more convenient.

Other Preparation Work

• Ensure the sensor's RS485 A/B lines are correctly connected to the adapter module's corresponding pins.
• The sensor's default baud rate is 4800, which matches the sample code configuration.

Sample Code

#include <SoftwareSerial.h>
SoftwareSerial mySerial(2, 3);                                        //TX,RX
uint8_t Com[8] = { 0x01, 0x03, 0x00, 0x00, 0x00, 0x03, 0x05, 0xCB };  //Chlorophyll concentration, temperature, fluorescence intensity
float chi, tem, fi;

void setup() {
  Serial.begin(9600);
  mySerial.begin(4800);
}
void loop() {
  Chlorophyll_Temperature_FI();
  Serial.print("Chlorophyll = ");
  Serial.print(chi, 1);
  Serial.print(" ug/L ");
  Serial.print(" FI = ");
  Serial.print(fi, 1);
  Serial.print(" RFU");
  Serial.print(" Temperature = ");
  Serial.print(tem, 1);
  Serial.println("°C");
  delay(1000);
}

void Chlorophyll_Temperature_FI(void) {
  uint8_t Data[12] = { 0 };
  uint8_t ch = 0;
  bool flag = 1;
  long timeStart = millis();
  long timeStart1 = 0;
  while (flag) {

    if ((millis() - timeStart1) > 100) {
      while (mySerial.available() > 0) {
        mySerial.read();
      }
      mySerial.write(Com, 8);
      timeStart1 = millis();
    }

    if ((millis() - timeStart) > 1000) {
      Serial.println("Time out");
      return -1;
    }

    if (readN(&ch, 1) == 1) {
      if (ch == 0x01) {
        Data[0] = ch;
        if (readN(&ch, 1) == 1) {
          if (ch == 0x03) {
            Data[1] = ch;
            if (readN(&ch, 1) == 1) {
              if (ch == 0x06) {
                Data[2] = ch;
                if (readN(&Data[3], 8) == 8) {
                  if (CRC16_2(Data, 9) == (Data[9] * 256 + Data[10])) {
                    chi = (Data[3] * 256 + Data[4]) / 10.0;
                    tem = (Data[5] * 256 + Data[6]) / 10.0;
                    fi = (Data[7] * 256 + Data[8]) / 10.0;
                    flag = 0;
                  }
                }
              }
            }
          }
        }
      }
    }
  }
}

uint8_t readN(uint8_t *buf, size_t len) {
  size_t offset = 0, left = len;
  int16_t Tineout = 500;
  uint8_t *buffer = buf;
  long curr = millis();
  while (left) {
    if (mySerial.available()) {
      buffer[offset] = mySerial.read();
      offset++;
      left--;
    }
    if (millis() - curr > Tineout) {
      break;
    }
  }
  return offset;
}

unsigned int CRC16_2(unsigned char *buf, int len) {
  unsigned int crc = 0xFFFF;
  for (int pos = 0; pos < len; pos++) {
    crc ^= (unsigned int)buf[pos];
    for (int i = 8; i != 0; i--) {
      if ((crc & 0x0001) != 0) {
        crc >>= 1;
        crc ^= 0xA001;
      } else {
        crc >>= 1;
      }
    }
  }

  crc = ((crc & 0x00ff) << 8) | ((crc & 0xff00) >> 8);
  return crc;
}

Result

The serial monitor displays the Chlorophyll value, fluorescence intensity, temperature data collected by the sensor.